Access Server’s OS Console from the LOM service Processor:
Server Models : SunFire V100/V120/V1280/E2900 and Netra 1280/1290
You can use below command to navigate between Server OS console and LOM port:
connecting to console from LOM prompt:
sc/lom>console
Returning to LOM from the Server console
presss #. ( # followed by a dot)
How to send break signal to console so that we can launch the server at OK> Prompt:
sc/lom>break – server will be landed into ok prompt
Access Server OS Console from SUN ALOM Service Controller :
Server Models : Sun Fire V125, V210, V240, V245, V250, V440, V445, Netra 210, 240, 440 …
Once you connect to the ALOM port, you can use below commands. Please note that any time you want to exit the serial console just press ‘#.’ ( # followed by dot) you will return to ALOM.
SC > console
Console session already in use. [view mode]
Enter #. to return to ALOM.
(Press #.)
SC > console -f
Warning: User currently has write permission to this console and forcibly removing them will terminate any current write actions and all work will be lost. Would
you like to continue? [y/n]y
Enter #. to return to ALOM.
How to send break signal to console so that we can launch the server at OK> Prompt:
SC> break
Access Server’s OS Console from SUN ILOM Service Processor:
Server Models:Sun Fire X4100, X4100 M2, X4140, X4150, X4170, X4200, X4200 M2, X4250, X4270, X4600, X4600 M2 …
Once you connect to ILOM SP you can use below command to connect to the console. Please note you can use “ESC ( ” to disconnect from console any time, then you will return to ILOM.
-> start /SP/console
Are you sure you want to start /SP/console (y/n)? y
Serial console started.
To stop, type ESC ( (Press Enter key to view serial console) in case if you notice that serial console is already in use just stop it once and restart.
-> stop /SP/console
Are you sure you want to stop /SP/console (y/n)? y
How to send break signal to console so that we can launch the server at OK> Prompt:
-> set /HOST send_break_action=break
and then
-> start /SP/console
Access Server’s OS Console from ELOM Service Processor:
Server Models : Sun Fire X2100, X2100 M2, X2200, X2200 M2
Once you connect to ELOM SP port you can user below commands to start and stop the consoles. Please note that you can use ESC ( to disconnect from the serial console anytime, then you will return to ELOM.
/SP -> start /SP/AgentInfo/console
console activate successful
press ESC ( to terminate session…
in case if you notice the Serial console is already in use you can stop it with below command and start it again
/SP -> stop /SP/AgentInfo/console
console de-activate successful
How to send break signal to console so that we can launch the server at OK> Prompt:
-> set /HOST send_break_action=break
and then
-> start /SP/console
Access console from RSC Service Processor
Server Models: Sun Fire v480, Sun Fire V490, Sun Fire v880, Sun Fire V880z and Sun fire V890
Once you connect to RSC Service Processor, you can use below command to navigate betweek OS console and RSC prompt.
RSC> console <- it will take you to the Server OS console
anytime if you want to return to the RSC prompt from the OS console just press “~.” ( tilda’~’ followed by a dot ‘.’)incae if the escape character “~” not working you can find it from the OS level using the command
# /usr/platform/`uname -i`/sbin/rscadm show escape_char
escape_char=”*”
if you think someone already using console, or console is busy you can still grab the console by resetting RSC which will forcibly close all the current connection
rsc> resetrsc
or from OS console prompt
#/usr/platform/`uname -i`/sbin/rscadm resetrsc
How to send break signal to console so that we can launch the server at OK> Prompt:
RSC >break – server will be landed into ok prompt
Below is the reference information to know which hardware model supports what type of console
Console Types :
Server Models : SunFire V100/V120/V1280/E2900 and Netra 1280/1290
You can use below command to navigate between Server OS console and LOM port:
connecting to console from LOM prompt:
sc/lom>console
Returning to LOM from the Server console
presss #. ( # followed by a dot)
How to send break signal to console so that we can launch the server at OK> Prompt:
sc/lom>break – server will be landed into ok prompt
Access Server OS Console from SUN ALOM Service Controller :
Server Models : Sun Fire V125, V210, V240, V245, V250, V440, V445, Netra 210, 240, 440 …
Once you connect to the ALOM port, you can use below commands. Please note that any time you want to exit the serial console just press ‘#.’ ( # followed by dot) you will return to ALOM.
SC > console
Console session already in use. [view mode]
Enter #. to return to ALOM.
(Press #.)
SC > console -f
Warning: User currently has write permission to this console and forcibly removing them will terminate any current write actions and all work will be lost. Would
you like to continue? [y/n]y
Enter #. to return to ALOM.
How to send break signal to console so that we can launch the server at OK> Prompt:
SC> break
Access Server’s OS Console from SUN ILOM Service Processor:
Server Models:Sun Fire X4100, X4100 M2, X4140, X4150, X4170, X4200, X4200 M2, X4250, X4270, X4600, X4600 M2 …
Once you connect to ILOM SP you can use below command to connect to the console. Please note you can use “ESC ( ” to disconnect from console any time, then you will return to ILOM.
-> start /SP/console
Are you sure you want to start /SP/console (y/n)? y
Serial console started.
To stop, type ESC ( (Press Enter key to view serial console) in case if you notice that serial console is already in use just stop it once and restart.
-> stop /SP/console
Are you sure you want to stop /SP/console (y/n)? y
How to send break signal to console so that we can launch the server at OK> Prompt:
-> set /HOST send_break_action=break
and then
-> start /SP/console
Access Server’s OS Console from ELOM Service Processor:
Server Models : Sun Fire X2100, X2100 M2, X2200, X2200 M2
Once you connect to ELOM SP port you can user below commands to start and stop the consoles. Please note that you can use ESC ( to disconnect from the serial console anytime, then you will return to ELOM.
/SP -> start /SP/AgentInfo/console
console activate successful
press ESC ( to terminate session…
in case if you notice the Serial console is already in use you can stop it with below command and start it again
/SP -> stop /SP/AgentInfo/console
console de-activate successful
How to send break signal to console so that we can launch the server at OK> Prompt:
-> set /HOST send_break_action=break
and then
-> start /SP/console
Access console from RSC Service Processor
Server Models: Sun Fire v480, Sun Fire V490, Sun Fire v880, Sun Fire V880z and Sun fire V890
Once you connect to RSC Service Processor, you can use below command to navigate betweek OS console and RSC prompt.
RSC> console <- it will take you to the Server OS console
anytime if you want to return to the RSC prompt from the OS console just press “~.” ( tilda’~’ followed by a dot ‘.’)incae if the escape character “~” not working you can find it from the OS level using the command
# /usr/platform/`uname -i`/sbin/rscadm show escape_char
escape_char=”*”
if you think someone already using console, or console is busy you can still grab the console by resetting RSC which will forcibly close all the current connection
rsc> resetrsc
or from OS console prompt
#/usr/platform/`uname -i`/sbin/rscadm resetrsc
How to send break signal to console so that we can launch the server at OK> Prompt:
RSC >break – server will be landed into ok prompt
Below is the reference information to know which hardware model supports what type of console
Console Types :
Lights Out Manager (LOM)LOM
Advanced LOM (ALOM)
Advanced LOM for Solaris Sun4v kernel architecture (ALOM4v)
Integrated Lights Out Manager (ILOM)
Embedded Lights Out Manager (ELOM)
Sun Remote System Console (RSC) for system management
Embedded Service Processor (SP).
Sun Netra X1ALOM
Sun Netra T1400/1405
Sun Netra T1 AC200
Sun Netra T1 DC200
Sun Fire V100
Sun Fire V120
Sun Netra 20
Sun Netra 1280 **
Sun Netra 1290 **
Sun Fire V1280 **
Sun Fire E2900 **
** The LOM for the Sun FireV1280/E2900 is delivered as part of the ScApp.
See the Hardware/PROM: 5.20.16: Sun Fire E6900/E4900/E2900/6800/4800/4810/3800/V1280 Netra 1280 and Netra 1290 Systems FW Update
Sun Fire V125ALOM4v
Sun Fire V210
Sun Fire V215
Sun Fire V240
Sun Fire V245
Sun Fire V250
Sun Fire V440
Sun Fire V445
Sun Fire T1000ILOM
Sun Fire T2000
Sun SPARC Enterprise T1000
Sun SPARC Enterprise T2000
Sun Netra T2000
Sun Blade T6300
Sun Fire X4100ELOM
Sun Fire X4200
Sun Fire X4500
Sun Fire X4600
Sun Fire X4100 M2
Sun Fire X4200 M2
Sun Fire X4600 M2
Sun Blade 6000 CMM
Sun Blade 8000 CMM
Sun Netra X4200 M2
Sun Blade X6220
Sun Blade X6240 Server Module
Sun Blade X6220 Server Module
Sun Blade X6275 Server Module
Sun Blade X6270 Server Module
Sun Blade X6440 Server Module
Sun SPARC Enterprise T5140 – ILOM 2.x or 3.x + ALOM4v emulation
Sun SPARC Enterprise T5240 – ILOM 2.x or 3.x + ALOM4v emulation
Sun SPARC Enterprise T5440 – ILOM 2.x or 3.x + ALOM4v emulation
Sun SPARC Enterprise T5120
Sun SPARC Enterprise T5220
Sun Blade T6340 Server Module – ILOM 2.x or 3.x + ALOM4v emulation
Sun Blade T6320
Sun Fire X2100 M2RSC
Sun Fire X2200 M2
Sun Blade X6250 Server Module – ELOM (no longer updated), ILOM 2.x or 3.x
Sun Blade X6450 Server Module – ELOM (no longer updated) ILOM 2.x or 3.x
Sun Fire V890SP
Sun Fire V490
Sun Fire V880
Sun Fire V480
Sun Fire 280R
Sun Enterprise 250
Sun Fire V20z
Sun Fire V40z
0 comments:
Post a Comment